Z probe using feeler gauge

This topic contains 15 replies, has 9 voices, and was last updated by  Barry 2 months, 4 weeks ago.

Viewing 16 posts - 1 through 16 (of 16 total)
  • Author
    Posts
  • #105035

    Yann Vautrin
    Participant

    Hi all,

    Fine tuning my mpcnc, I am now looking at a Z probe, was thinking to use spark plug feeler gauge, as they are calibrated, and everyone has one in is car toolbox!

    If my understanding is right, i wire one of the feeler gauge to the Z min signal pin, and a crocodile clip on the too bit connected to the (-) negative Z min pin?

    Just confirm I am not going to f**k it up! 😉

    #105063

    Ryan
    Keymaster

    Yes, perfect Z probe.

    #105146

    Yann Vautrin
    Participant

    Done!

    Attachments:
    1 user thanked author for this post.
    #106414

    Bill
    Participant

    I’ve been wondering about using a sheet of aluminum foil and doing a mesh bed level… You’d probably want to have some method for holding it down though.

    1 user thanked author for this post.
    #106433

    Yann Vautrin
    Participant

    Was thinking about it too, but how to keep it perfectly in contact with the spoilboard?

    #106468

    Tim W
    Participant

    spray glue?

    #106484

    Bill
    Participant

    You might be able to just use water to get it to stick in place. Glue isn’t liable to be good since it’ll stay behind when you pull the foil to start your actual cuts.

    1 user thanked author for this post.
    #106487

    Barry
    Participant

    As long as the spoil board isn’t mdf…

    #106498

    Bill
    Participant

    Yeah, when you put water on MDF you end up having to wait a long time for it to dry then longer yet for the resurface to finish. 🙂 Saran wrap first, then water for the foil to stick to or just wax the surface before sprinkling?

    #106534

    Barry
    Participant

    Yeah, when you put water on MDF you end up having to wait a long time for it to dry then longer yet for the resurface to finish. 🙂 Saran wrap first, then water for the foil to stick to or just wax the surface before sprinkling?

    Or just fit a switch to the spindle.  Though honestly I’m not sure why you’d want to probe the whole bed anyway.  Just surface it and be done with it.

    1 user thanked author for this post.
    #106842

    GTKplusplus
    Participant

    I’ve been wondering about using a sheet of aluminum foil and doing a mesh bed level… You’d probably want to have some method for holding it down though.

    Or you can simply use Aluminum tape. I did a couple of times for cutting really big vynil stickers, since I didn’t trust my leveling and I used a different mdf board to hold them. It works well enough, and it’s quick to apply.
    Not that easy to remove though, so that may be an issue.

    #106843

    JDGreen
    Participant

    You all have me thinking…How about putting several pieces of aluminum tape at the 9 or 16 or however many mesh points to want to use? Maybe router a little groove for a small wire to connect them all?

    #106844

    Tim
    Participant

    Done!

    What type of solder did you use? Also aluminum wire?

    #106845

    Bryan J
    Participant

    Done!

    What type of solder did you use? Also aluminum wire?

    I just made one of these to go with my dual endstop install.  At first it wouldn’t stick even after degreasing and scuffing, but I cranked up the heat on my (Hakko) soldering iron and focused on just getting solder on the gauge.  It eventually took a small spot of solder and then I was able to attach a pre-tinned wire to it.  I guess the key is the gauge needs more heat than the copper wire.  Once the solder is on the gauge you don’t need such high heat to bond the wire to it.

    Now I’m trying to figure out the best quick connect and cable management.

    #106849

    Bill
    Participant

    Yes, the gauge has enough mass to act as a pretty good heat sink. That’s what my 140W soldering gun is for. 🙂

    #107358

    Barry
    Participant

    Yes, the gauge has enough mass to act as a pretty good heat sink. That’s what my 140W soldering gun is for. 🙂

    Propane torch works pretty well too.

Viewing 16 posts - 1 through 16 (of 16 total)

You must be logged in to reply to this topic.