August 7, 2017 at 7:22 pm #40314
Hey guy it’s me again, machine was working beautifully lately, today I left it drawing and suddenly noticed z axis dropped, it seems the top blue part is not attached rwell or so, it can still run up and down by the motor.
But, when I put Sligh pressure even from the bottom, the whole z axis moves up so something got loose for sure.
Any idea how to fix this issue?
Attachments:August 7, 2017 at 7:37 pm #40322
Check the locknut. It could be loose or broken letting the coupling nut and the allthread to slide up and down.August 7, 2017 at 7:44 pm #40323
Hey! Thanks for the fast reply, do you refer to the 3 bolts on the blue thing itself?August 7, 2017 at 7:54 pm #40325
On the middle assembly where a coupling nut goes.
Of course the pineapple itself shouldn’t be loose either. Do you see the blue pineapple move when you push from bottom?August 7, 2017 at 8:09 pm #40326
I think I figure it out, it’s connected well to the rod going down, so the one with a spiral texture on it. But it got disconnected from the rod going out of the motor(smooth looking rod)
Still not sure what’s the fixAugust 8, 2017 at 4:07 am #40340
Either a little tighter on the upper screw closest to the stepper, or if you think you might break it, a little superglue. If the coupler ever breaks the plastic can be scraped off the stepper shaft without hurting it. Also, once you have it back in place, run the black plate that’s under it right up against it(go up). That way the bearing takes the weight, not just a piece of hanging plastic.
Look at mine for an example.
https://goo.gl/photos/eSUJdtn3ruR9NKzo7August 8, 2017 at 4:15 am #40341
Thanks a lot, super glue worked like magic for now, finished my 4 color pen drawing 😀
I hope it will be strong enough for drilling later on too, otherwise I’ll come back to figure out what piece I have to replace
Attachments:August 8, 2017 at 4:38 am #40355
Also, once you have it back in place, run the black plate that’s under it right up against it(go up). That way the bearing takes the weight, not just a piece of hanging plastic.
Don’t forget that step.August 8, 2017 at 8:28 am #40369
4 color pen drawing!!! What is that.August 8, 2017 at 8:31 am #40370
It looks like you might have tried to lube all your bearings, for the most part you should consider them sealed and not able to be lubed. Some lubes do not interact well with PLA plastic, your parts could start to degrade. The coupler issue could be from that. All that lube is just going to make milling debris stick to your machine.August 8, 2017 at 10:09 am #40375
Hey Ryan !
its basically using 4 different pens, normal 2 cent pens from the office shop, and use them to make a full color drawing like that one.
about the lube, as those drawings take ages, at night I heared horrible squeaking noise coming from the Z axis, it was 2 AM and i wasnt very careful with my aiming. the noise did stop at least and i cleand up the mess later on.
so far so goodAugust 8, 2017 at 11:42 am #40377
Awesome, I added that to the gallery, keep it up!August 8, 2017 at 11:58 am #40378
Omri, I have no idea how you accomplished that drawing but it is incredible. As a classic car guy it is even more amazing.August 8, 2017 at 3:29 pm #40394
Yes same here ! I’d be very much keen to know how you generated that gcode !August 9, 2017 at 2:16 pm #40522
I’ll add my agreement – That is pretty darn cool. Any details on how you did it would be appreciated!August 12, 2017 at 7:31 am #40873
Hey guys ! happy you all like it 😀
its actually pretty complex, involves 4 different programs and allot of patience,
took me over 7 month of non stop machine drawing at least 4 days per week.
maybe ill make a tutorial later on when i reach more crazy results and this becomes more normal for me 🙂August 12, 2017 at 9:28 am #40907
Do you have a website where you sell your art?
Pen on paper, summer swim, machine drawing. #penplotter #penart #pen #penplot #instafineliner #instaart #drawing #penonpaper #musclecar #racecar #yellow #sketch #crosshatch #hatching #fineliner #cardrawing #colordrawing #colorpen #checker #vivid #swimwear #bikini #summerfart
A post shared by Om (@omrbig) on
Really great work.August 12, 2017 at 11:43 am #40924
Hey guys ! happy you all like it 😀 its actually pretty complex, involves 4 different programs and allot of patience, took me over 7 month of non stop machine drawing at least 4 days per week. maybe ill make a tutorial later on when i reach more crazy results and this becomes more normal for me 🙂
Whaaaat ???August 12, 2017 at 2:39 pm #40940
And Jeffeb3, I’m not really selling organized yet, just sold few pieces and some were used as an album cover by an Irish band 😀
At the moment busy trying ti apply for art funding so I can push it all a bit further and make a more serious series of drswing or even paintings if I can solve some – brush going to dip in paint every few strokes – problemsAugust 12, 2017 at 3:13 pm #40944
brush going to dip in paint every few strokes – problems
I used to have something similar, they actually work pretty well.September 13, 2017 at 5:28 am #43745
Hey Berry !
brush pens are indeed super nice, ive been trying to work with them with the principal of a V-bit method, since they do have somwhat the same shape, but i found brushes are very hard to control. they are only fun in more free style 😀
A post shared by Om (@omrbig) on <time style=” font-family:Arial,sans-serif; font-size:14px; line-height:17px;” datetime=”2016-11-10T20:21:10+00:00″>Nov 10, 2016 at 12:21pm PST</time>
<script async defer src=”//platform.instagram.com/en_US/embeds.js”></script>
this was done using acrylic paint and a brushSeptember 20, 2017 at 2:50 pm #44310
Outstanding stuff! (Just saw Ryan’s post on the homepage…wondering how I missed this until now!)
As for a brush…have you heard of a “fude nib” pen? I recently discovered them and have been having a bunch of fun doodling with one. They look like a fountain pen that was dropped on the ground – but the tip is bent like that on purpose so it can get brush like line variations (they were originally developed for Japanese calligraphy which is traditionally done with a brush.)
I have a <$10 Hero 9018 which is a fountain pen – but there are also felt/hair versions that may be easier to work with in a machine. With the fountain pen you’d have to come up with a way to adjust the angle of the pen to change the line – with the felt/hair versions simple z changes should work.
Basically it would give you a brush like instrument that self-feeds ink so you don’t have to keep dipping it and should get a more consistent result.September 21, 2017 at 12:18 am #44326
Hey Jason , thanks for the tip ! looks like it might work out wellOctober 13, 2017 at 5:16 pm #45904
You sir are amazing. I love seeing other amazing uses for the mpcnc. Keep up the great work bud. Keep the pictures coming. I am blown away at your results.
You must be logged in to reply to this topic.