using a spindle on the low rider

New Home Forum LowRider Your Builds – LowRider using a spindle on the low rider

This topic contains 22 replies, has 3 voices, and was last updated by  Ailton Lopes 6 months ago.

Viewing 23 posts - 1 through 23 (of 23 total)
  • Author
    Posts
  • #86773

    dane
    Participant

    hi there, another lowrider thread for me lol, so i had bought a 52mm spindle to use on my mpcnc, and now im thinking i would like to use it on my lowrider build, unfortunatly i dont see anywhere on thingiverse where there is a spindle mount for thew low rider. im sure someone has made one, but i dont know where to find the design. lol can someone help me out please

    #86824

    Ismail
    Participant

    I’ll help you. I have already made an adaptor in Inventor which i can redesign for your spindle. I need to know it’s brand and model number or outer diameter and mounting hole positions.

    1 user thanked author for this post.
    #87493

    dane
    Participant

    its a chinease 52mm spindle bought it off banggood and sorry i didn’t see your reply i didn’t get a notification thank you in advance

    Attachments:
    #87597

    dane
    Participant

    and the mounting hole locations come from the 611 plate of the lowrider

    #87646

    Ismail
    Participant

    This will be easy 🙂

    Tomorrow there will be more than enough time for me to design it because my lectures in university do not start until the evening.

    2 users thanked author for this post.
    #87908

    dane
    Participant

    Ismail. i very very much appreciate it, thank you in advance

    #87961

    Ismail
    Participant

    https://www.thingiverse.com/thing:3412102

    https://drive.google.com/open?id=1wMyr5_Uht4_H1BxjwFpCEcA1KPEUz8xj

    Done! hopefully this one will do the trick. And it does not even use an exorbitant amount of filament contrary to what i feared. I made all the hole diameters 4,5mm for M4 screws. It’s width is about 80-90mm.

     

     

    52mm-spindle-adapter-assembly

    3 users thanked author for this post.
    #88007

    dane
    Participant

    what are the 2 tabs on the inside of the holder for? to bottom the spindle on for height?

    #88037

    Ismail
    Participant

    There are three of them which will give it a 3 point connection with the spindle. I thought this will be good to compensate for clearance.

    #88040

    dane
    Participant

    i just finished printing this and those 3 things are interfering with the spindle and the spindle wont sit square in the mount. can  u make a mount like the pic below with the 611 plate bolt pattern like a ring on the bottom so that the spindle would be able to slide through the hollow tube? 2 bolts instead of 3 please?

    Attachments:
    #88042

    dane
    Participant

    same style mount just hollow tube like the one above

    #88052

    Ismail
    Participant

    How is this one?

    52mm-spindle-adapter-2

    52mm-spindle-adapter-2-bottom-1

    I have updated the files on Thingiverse. “52mm spindle holder V2”

    #88056

    Ismail
    Participant

    (Accidental double post while trying to insert a second image)

    #88114

    dane
    Participant

    that should work ok, thank you very much for taking the time out of your day to help me

    1 user thanked author for this post.
    #88115

    dane
    Participant

    also it looks like the bottom plate is only attached to the tube halfway, that will be hard to print without supports

    #88116

    dane
    Participant

    it should be made with full attachment of the 2 parts

    #88117

    dane
    Participant

    also there no listing for the part on thingiverse i put 52mm spindle holder V2 into the search and gets nothing

    #88151

    Ismail
    Participant

    It’s all here: https://www.thingiverse.com/thing:3412102

    1 user thanked author for this post.
    #88293

    dane
    Participant

    hey there sorry to say. there has to be a tolerance for it to work i printed it out and couldnt get the spindle in without forcing. it should be loose so that the bolts hold it tight also the slice where the bolts go has to go through the base as well

    #88814

    Ailton Lopes
    Participant

    Hey guys! I’m enjoying this discussion! I tried modeling a part for the 500W chinese spindle but I have no experience in that area. I’m just a simple, poor and mortal History`s teacher

    Thanks for sharing!!

    1 user thanked author for this post.
    #88846

    Ismail
    Participant

    You are welcome!

    Btw. i have added a tolerance of 0.6mm to the hole and extruded the slice all the way through. It’s also in the link above. File name is “52.6mm adapter with complete slice”.

    1 user thanked author for this post.
    #89110

    Ailton Lopes
    Participant

    I will print this one! Thanks for sharing

    #89954

    Ailton Lopes
    Participant

    Hey guys! I printed this 3d model (52,6mm) and it works perfectly!

     

Viewing 23 posts - 1 through 23 (of 23 total)

You must be logged in to reply to this topic.