Questions for the intermediate walk through

New Home Forum Updates Questions for the intermediate walk through

This topic contains 16 replies, has 7 voices, and was last updated by  Chris Pieper 1 month, 3 weeks ago.

Viewing 17 posts - 1 through 17 (of 17 total)
  • Author
    Posts
  • #14905

    Ryan
    Keymaster

    ESTLCAM – 2.5D Routing- Intermediate

    Ask your questions here and I will try and answer you and clarify the walkthrough.

    2 users thanked author for this post.
    #27589

    smit
    Participant

    hey can your share your estlcam setup with me, because i tried using nema 23 and 17 motor on 20v when i program the ramps 1.4 board on A4988 motor drivers the motors does not move.

    #35134

    Alex Hodge
    Participant

    Hey Ryan,
    Looks like the ESTLCAM file in your intermediate walkthrough is an old version and cannot be used by the current version of ESTLCAM. Not sure what you can do about it. There doesn’t seem to be any way to update an e8 file to an e10 file and if you try renaming the extension, it just tells you “this file was created by an older version and it isn’t possible to open it”…or something along those lines.
    Just a heads up.

    #35136

    Ryan
    Keymaster

    Aww Man, I will have to redo it. The walkthrough should still be relevant though. Thanks for the heads up.

    #100340

    ddrehs
    Participant

    Are the files available for this project

    #100344

    Ryan
    Keymaster

    Yes, linked in the first post.

    #100661

    ddrehs
    Participant

    Thanks got them.

    #107539

    Chris Pieper
    Participant

    I am unable to run EstlCam because I have a Linux machine, but I have other means to generate gcode. I have a basic question about the Z coordinates. Is the z=0.0 the top of the workpiece or the top of the spoilboard? I have another small router where z=0.0 is the top of the workpiece so cuts go to negative Z. If the MPCNC strategy is to use the top of the workpiece as Z=0, then how do you lift the router off the spoilboard (where it goes after the steppers are powered down) and then set the Z coordinate to zero? Sorry if this is not the right place to ask, I’m trying to follow the example but I’m stuck on this point. Thanks!

    #107549

    Tim
    Participant

    I am unable to run EstlCam because I have a Linux machine, but I have other means to generate gcode. I have a basic question about the Z coordinates. Is the z=0.0 the top of the workpiece or the top of the spoilboard? I have another small router where z=0.0 is the top of the workpiece so cuts go to negative Z. If the MPCNC strategy is to use the top of the workpiece as Z=0, then how do you lift the router off the spoilboard (where it goes after the steppers are powered down) and then set the Z coordinate to zero? Sorry if this is not the right place to ask, I’m trying to follow the example but I’m stuck on this point. Thanks!

    z=0.0 is literally wherever you want. if you set it as the top of your workpiece in your software, then position the tip of the tool right at the top of your workpiece before turning your board on, it will set the z0 to that point. Or, you could move it to that position after the machine is powered on and then type g92 z0 in to the manual command input and it will set the current machine position to z0.

    1 user thanked author for this post.
    #107573

    Jeffeb3
    Participant

    I am unable to run EstlCam because I have a Linux machine

    FWIW, I run EstlCAM in wine.

    Out of curiosity, what CAM are you using?

    1 user thanked author for this post.
    #107579

    Chris Pieper
    Participant

    Sorry,  I’m not sure what CAM is… if it is the means to convert images to gcode, then I use image-to-gcode, which comes with LinuxCNC, and I have also used Inkscape with a gcode plugin. As you might have guessed, I barely know what I’m doing but I’m motivated to learn. I really appreciate the help offered by others like yourself. Thanks!

    #107581

    Jeffeb3
    Participant

    Yep. CAM is how you make gcode from your design file. It might be an engrave from an image or it might be defining parts and holes. EstlCAM is what’s in the tutorials but there are others.

    1 user thanked author for this post.
    #107590

    Chris Pieper
    Participant

    Jeffb3, I just installed Wine on my Linux machine. How do you get the EstlCAM executable? Do you install it on Windows and then copy the executable or is there another way? Thanks.

    #107598

    Jeffeb3
    Participant

    You download the installer from estlcam.de. Technically, I used playonlinux, IIRC. I honestly can’t remember the steps I took to get it installed.

    1 user thanked author for this post.
    #107608

    Chris Pieper
    Participant

    Thanks. I tried but when I try to run the executable, it complains about not being able to find some Windows-like path… I’ll keep poking away at it. I may shoot for the moon and try to configure LinuxCNC…. hopefully there is some info on the forum for this. The challenge will likely be to configure it for this router. I should probably crawl before I try to fly…

    #107610

    Jeffeb3
    Participant

    Bummer. I haven’t done it with the latest version or my newest machine. Maybe I’ll take better notes this time.

    You might try these instructions for some foss tools, which I assume are available on Linux:

    https://alexpgh.github.io/foss-toolchain-mpcnc/

    1 user thanked author for this post.
    #107611

    Chris Pieper
    Participant

    Wow! That looks great. I have FreeCAD and openSCAD but haven’t used either much. I tend to use openSCAD because it’s easy for me to start with (all programming). I’ll study this information but at first glance it looks great.

Viewing 17 posts - 1 through 17 (of 17 total)

You must be logged in to reply to this topic.