- March 22, 2017 at 7:26 am #29990
I have been trying to connect the ramp to my computer, but all that happens is I get a printer side error. I have no idea how to use an arduino, I doubt I have the steppers connected correctly since the wiring I got doesn’t match the assembly pictures.
Attachments:March 22, 2017 at 7:34 am #29996
Where did you get your ramps from? Do you have my wiring kit? Do you have a resistor on terminal t0?March 22, 2017 at 7:40 am #29997
I got everything from you, yes and I thought I got the wiring kit, it doesn’t seem to have those extra wire connectors.March 22, 2017 at 7:41 am #29998
Shown in the second picture here, https://www.v1engineering.com/assembly/ramps-wiring/.
There should be a resistor in the bag with the pulleys and 3 bearings plug it in and you should be good to go.March 22, 2017 at 7:43 am #29999
You also have a steppers plugged into a port with no driver and a drive stepper plugged into the extruder port, did you set the voltage on the extra driver? You aren’t using my wiring harness in the picture.March 22, 2017 at 7:48 am #30000
What does the resistor look like?March 22, 2017 at 7:51 am #30002
Attachments:March 22, 2017 at 7:53 am #30004
…and what are the wire harnesses? The zip ties?March 22, 2017 at 7:55 am #30005March 22, 2017 at 8:03 am #30006
How do I install the resistor and where do the steppers go?March 22, 2017 at 8:05 am #30007
That last link walks you through every step.March 22, 2017 at 8:17 am #30008
Clearly, I am having trouble understanding your tutorials. I would really appreciate some additional instructions please.March 22, 2017 at 9:00 am #30013
Well… I’ve been trying to assemble this for about a year now to no avail. You said it would be no more difficult to build than a PC, it is clearly far more difficult. Is there any money back offer?March 22, 2017 at 9:33 am #30016
Here’s a shot of mine. Should give you a rough idea. https://goo.gl/photos/1n83tLafMVN5qNaX9
When I get home from work, I’ll take a better pic and annotate it.March 22, 2017 at 9:55 am #30020
Hi Sarah. You’ll get there. Although I’m not sure why it’s been a year.
This is the link to Ryan’s instructions on how to connect the resistor (shows where it goes) and the stepper motor wires. RAMPS Wiring There are 2 pictures for the steppers, one shows which Axis (X, Y, Z) belongs to each driver. The other shows the wires beside each corresponding driver. Make sure what you have matches the pictures ok. Then let us know how that works and what you need next.
The information is all there somewhere on the assembly section though. Just have a look through and make sure you follow each step precisely and it should go quite smoothly.
PhilMarch 22, 2017 at 10:21 am #30021
I’m back. If you are really having that hard of a time.
Look through the steps and either tell us what doesn’t make sense, or show a picture.
You are trying to figure out how to plug the ramps in , but You do not have it wired up correctly and I think you should get that sorted out before we deal with the computer part.
I sent you the link to the wiring page, and the assembly page. the assembly page actually shows how I how up the wiring harness with pictures so you know what it looks like. and the other has labels and such.March 23, 2017 at 3:40 am #30053
Ramps wiring. https://www.v1engineering.com/assembly/ramps-wiring/ You’re making a router, so ignore the “Adding and extruder” part.
Stepper wiring. https://www.v1engineering.com/assembly/wiring-the-steppers/ Looks like on your photo you have the steppers wired driectly to the ramps board.
You must be logged in to reply to this topic.