Not a low rider frame but a low rider soft(france)

New Home Forum LowRider Your Builds – LowRider Not a low rider frame but a low rider soft(france)

This topic contains 17 replies, has 3 voices, and was last updated by  richard 1 year, 6 months ago.

Viewing 18 posts - 1 through 18 (of 18 total)
  • Author
    Posts
  • #50184

    richard
    Participant

    Hello

    after having discovered the lowrider on thingiverse i tried to make one with the materials i have.
    so here is my solution closer to an openbuild profile solution nearly all the materials i use are 2nde hand materials i alredy have got except the stepper  and the openbuild wheel

    hope it ll works

    #50193

    Ryan
    Keymaster

    That looks closer to the crawlbot with a little hint of LowRider. Keep this thread updated so we can see the progress please!

    #50196

    richard
    Participant

    hello in fact after having seen the low rider on thingiverse i ve discovered the crawlbot thanks to you

    first movement this afternoon on y axis i ll try to update the topic

    thanks for all your work

    #50197

    Ryan
    Keymaster

    thanks for all your work

    Thanks for experimenting! I have some ideas for a LowRider update I hope to start prototyping soon.

    #50222

    richard
    Participant

    can t wait to see the updated low rider

    a view of my ‘lowrider’

    #50916

    richard
    Participant

    hello, a little question about power supply

    do the ramp and the arduino need to be power supplied?

    when i supply 12v to the ramp i can’t use the screen but if i connect the usb port of the arduino everything works

    is it normal or not?

    if not can i connect the 12v of the ramp to the jack of the arduino?

    thank you

    #50917

    Ryan
    Keymaster

    That means your 5V regulator is bad on the mega. You can make alterations to the Ramps (remove diode) and power the mega as well, or replace the 5V reg.

    #50918

    richard
    Participant

    ok thanks i ll check thanks a lot

    #51921

    richard
    Participant

    mistake / sorry

    #58305

    richard
    Participant

    hello,

    after having build a 90m2 workshop i m back with my lowrider.

    i made a few test today it seems ok

    i m looking for lcd extension is there a maximum length?

    can someonetell me what are the references of the connectors?

    and what is the type of wire?

    thanks

    #58307

    Felix
    Participant

    the LCD cables seem to be standart 1,275mm 0,05″ spaced ribbon cables. 10 wires wide.

    the connectors 2.54mm 0,1″ spaced 2×5 post connectors, you should find them easily at any relevant electronics store.

    Ryan is selling a 4′ cable so I think that should be ok, how much would you like to have?

    regards
    Felix

    1 user thanked author for this post.
    #58315

    richard
    Participant

    thanks

    i wanted to install 1.2m/1.5m so i needed 2.5m/3m for the 2 wire

    i leave in france so shipping representa significant cost for 2 wires

    i ll post picture tomorrow

    #58347

    richard
    Participant

    hello,

     

    here are my first try with 6mm router bit

    not as good i expected but correct

    another try with 1/8 router bit and another quality of mdf quite happy with the result no picture

    i have to learn and test bit, material, speed….

    #58352

    richard
    Participant

    another one

    #58406

    richard
    Participant

    hello

    after my first cutting test the speed control seems to be necessary

    an old belt sander out of work 1000w is the origin of my speed controller

    installed between the wall plug and the spindle plug and it works

    i have to print a small box for this and the switchgive the possibility to put on or off the spindle.

    i m not electrician it s my solution but you have to take your responsability

    if someone think it s dangerous please let me know and i delete this post

    #58459

    richard
    Participant
    #58463

    richard
    Participant

    mistake

    #58466

    richard
    Participant

    mistake

Viewing 18 posts - 1 through 18 (of 18 total)

You must be logged in to reply to this topic.