New build in Edmonton AB,CA

New Home Forum Mostly Printed CNC – MPCNC Your Builds – MPCNC New build in Edmonton AB,CA

This topic contains 13 replies, has 5 voices, and was last updated by  Garrett 2 months, 1 week ago.

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #97816

    David Corscadden
    Participant

    Just introducing myself and my new MPCNC. Its a 24×30 inch cut area running on a ramps 1.4 board and will have a foam needle cutter as well as a Dw660 and a dragknife for vinyl. Its up and running and just getting my head around the Estlcam software. The only trouble I have had was I could not enter the M92 steps/mm adjustment as it said the eeprom was not enabled ( it seems like its turned on in marlin). Might be my arduino mega board and I have a new one on its way. Mine has the cheap clone with the CH340 USB/serial chip and has given me trouble flashing so out it goes. I entered the new M92 settings in marlin and flashed it through the isp port until the new board arrives. BTW the parts were printed on my other conduit build an EMT-8 frame for my Anet A8 printer.

    This was a fun project and was amazed at the engineering and how well it all went together! Thank you for the plans!

     

    #97838

    Ryan
    Keymaster

    Awesome.

     

    I have new firmware in the works (ramps is done and available) that enables the eeprom again.

    1 user thanked author for this post.
    #97848

    David Corscadden
    Participant

    Thanks Ryan for the reply. I am running version 401 which I have changed to work with 20t pulleys and A4988 drivers for now (16t and drv8825 drivers on order,opps). Its working for now but that darn mega has to go, its a pain to have to pull the ramps to flash it thru the isp.  Have three of the boards and they all will flash fine , once, then will not flash again until you reflash the bootloader.

    #97853

    Jeffeb3
    Participant

    Thanks Ryan for the reply. I am running version 401 which I have changed to work with 20t pulleys and A4988 drivers for now (16t and drv8825 drivers on order,opps). Its working for now but that darn mega has to go, its a pain to have to pull the ramps to flash it thru the isp. Have three of the boards and they all will flash fine , once, then will not flash again until you reflash the bootloader.

    That is odd. It sounds like you are flashing off the bootloader. If you flash through USB, it shouldn’t be possible to remove the bootloader (the bootloader won’t let you). If you flash through ISP, then you could clobber the bootloader. If you do that, you shouls just flash the bootloader again through ISP and then use USB to flash new programs.

    #97856

    David Corscadden
    Participant

    Some of the chinese arduino megas with ch340 chip have a problem with the reset circuit no pulling the reset voltage low enough when flashing thru the usb port. Looks like the ones I have, have the problem. If you flash the bootloader then the mega is reset and is waiting for the program flash and takes it fine but if you try to upload a second time then it will not take the flash and they time out. If you press the reset button at the exact time that the download starts you can get them to flash. Been driving me nuts and for $15 boards, life is too short! Have some new ones coming in. Both my 3d printer and the MPCNC have the problem and will get new boards when they come in.

    #97862

    Jeffeb3
    Participant

    Oh, that’s annoying.

    #97918

    Jonathan
    Participant

    David that’s terrible luck with the mega boards. I’m hoping I don’t have that luck with mine. Have you thought about just adding a set of jumper wires to extreme the ISP, so you don’t have to remove the ramps each time.

     

    I really like your Emt8, and it took me a day to place where I saw it, and Then I remember I saw it on the Facebook group.

    #97920

    David Corscadden
    Participant

    Jonathan, yes I was thinking about wiring up a remote isp but I have them programmed for now and will use them until the new ones arrive. Still trying to get the third one going using some of the ideas I have found online.

    #98039

    David Corscadden
    Participant

    Yea! My new andruino mega’s just arrived and are working properly. I save the old ones for some other project. I will test on the mpcnc later to day or tomorrow.

    #98208

    David Corscadden
    Participant

    I didn’t destroy the second Sharpie and the crown turned out great, now to get it dirty…maybe tomorrow.

    #98312

    Ryan
    Keymaster

    Awesome, it’s tomorrow get it dirty!

    #98374

    David Corscadden
    Participant

    OK , its dirty, not too dirty 🙂 I was working in carbide create and forgot to set the retraction distance, opps. It worked well other than that. Don’t worry it was a scrap piece of pine I had kicking around. The better half was impressed! Thank you Ryan again for the great design.

    Attachments:
    1 user thanked author for this post.
    #98391

    Ryan
    Keymaster

    For a first run…..impressive!

    Glad you like it.

    #99665

    Garrett
    Participant

    wow, that is beautiful

Viewing 14 posts - 1 through 14 (of 14 total)

You must be logged in to reply to this topic.