(SOLD) Lowrider2 for Sale – Indiana

New Home Forum For Sale, Leftovers, Used Parts, Services Offered (SOLD) Lowrider2 for Sale – Indiana

This topic contains 14 replies, has 6 voices, and was last updated by  Mike @Pix2Proto 3 months ago.

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • #102248

    Mike @Pix2Proto
    Participant

    I am looking to sell my full LowRider 2 as I have run out of room in my shop.

    What is included:

    • All Printed Components
    • All Flat Stock Parts
    • All needed hardware
    • Stainless Steel Rails (Purchased from Speedy Metals)
    • Synthetos gShield v5 with GRBL installed and setup for the LR2
    • V1 Engineering Wiring Harness
    • V1 Engineering Power Supply
    • Unistrut Rails

    What would still be needed:

    • DeWalt 611 Spindle

    I estimate I have about $620 in my setup, looking to get ~$500 + shipping, O.B.O.

    -Mike

    #102252

    Mike @Pix2Proto
    Participant
    #102256

    Mike @Pix2Proto
    Participant
    #102379

    Kevin
    Participant

    Mike,

    Where in Indiana are you? I’m on the Northeast side of Indianapolis.

    I’m interested in getting started in CNC, and might be able to justify this as Father’s Day/Early Birthday present.  Especially if I can avoid shipping cost.

    Thanks,

    Kevin

    #102380

    Mike @Pix2Proto
    Participant

    Kevin,

    I am located in Lafayette, so not too far.  Why don’t you shoot me an email at [email protected] and we can discuss it further.

    #104919

    Dimitri
    Participant

    Hey Mike, I sent you an email. Thanks. I’m interested.

    1 user thanked author for this post.
    #104945

    Mike @Pix2Proto
    Participant

    Dimitri,

    Yes, it is still for sale. I have sent you a response e-mail.  It looks like shipping the long tubes would be prohibitive and even then the shipping cost for the rest will be costly.  Let me know.

    -Mike

    #105899

    Drew Worthen
    Participant

    Is this still available?  I’m in Indy and am very curious about this machine.  A friend of mine recommended it to me so I am just now researching.  Thanks a bunch.

    1 user thanked author for this post.
    #105915

    Mike @Pix2Proto
    Participant

    Drew,

    Yes, I still have the lowrider 2 available.  If you are interested, you can shoot me an email at [email protected] to discuss.

    -Mike

    #106281

    TJ
    Participant

    Mike, what size is your build?  I’m interested, and coming from KY so it’s far but not too far.

    1 user thanked author for this post.
    #106341

    Mike @Pix2Proto
    Participant

    TJ,

    Thank you for reaching out.  I apologize for not noting it on the forum, but Drew has put in an offer at this time.  If something falls through I will let you know.

    #106609

    Mike @Pix2Proto
    Participant

    @TJ,

    Drew has decided to go a different route for his CNC purchase, so this Lowrider 2 is still available if you are still interested.  I had the LR2 setup to have a 4’x4′ build area to be able to do 1/2 sheets of plywood and not taking up too much room in my shop.  Please let me know if you have any more questions!  You can also reach out to me via email at [email protected]

    Thanks,

    -Mike

    #108578

    Mike @Pix2Proto
    Participant

    This machine is still available if anyone is interested

    #108746

    Dennis
    Participant

    Sending email now.

    #109177

    Mike @Pix2Proto
    Participant

    Thank you all for the interest — the LR2 has been sold.

Viewing 15 posts - 1 through 15 (of 15 total)

You must be logged in to reply to this topic.