Archim2 back to the Default

New Home Forum Mostly Printed CNC – MPCNC Troubleshooting – MPCNC Archim2 back to the Default

This topic contains 7 replies, has 2 voices, and was last updated by  Ryan 1 week, 5 days ago.

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #105552

    Gordon
    Participant

    My Archim2 board will not work after trying to do a flash

    Am I using the correct Marlin which one should I use?

    MARLIN-DUAL-END-STOPS or Marlin-MPCNC_Archim2_T8_16T_LCD_16step

    Just what is the correct Marlin to use could you give me the link to put this back to the default build

    I tried Marlin-c4c3fc45d198476bf22ef69800a8a3f8e18707e3.zip

    And others with no results

    Marlin says upload was Verify successful

    but when I run Repetier-Host

    I get this message Error Printer halted kill called

    How do I enter any Gcodes without using Repetier-Host

    Is there a different program to enter G0 X20 to test my board

    #105578

    Ryan
    Keymaster

    y Archim2 board will not work after trying to do a flash Am I using the correct Marlin which one should I use? MARLIN-DUAL-END-STOPS or Marlin-MPCNC_Archim2_T8_16T_LCD_16step

    I don’t know what wires you have?

    Just what is the correct Marlin to use could you give me the link to put this back to the default build I tried Marlin-c4c3fc45d198476bf22ef69800a8a3f8e18707e3.zip And others with no results

    The above two are the only ones that work, I have no idea what file that is. Please look through the firmware page again for flashing instructions.

    How do I enter any Gcodes without using Repetier-Host Is there a different program to enter G0 X20 to test my board

    Repetier host is the easiest way other than using your screen.

     

    Before I answer any more questions on your three posts, please, please upload some pictures of what you have. This will save us all a lot of time asking you tiny questions.

    #105582

    Gordon
    Participant
    You said The above two are the only ones that work, I have no idea what file that is. Please look through the firmware page again for flashing instructions.
    I use this
    A preconfigured Marlin4due Firmware is preloaded onto the board. Source code for this firmware is here.
    /Marlin4Due

    and that worked

     

     

    #105583

    Ryan
    Keymaster

    If that link is from the ultimachine site, it is generic, old, and not configured for any machine or LCD’s. Please look at my firmware page.

    arch

     

    Attachments:
    #105615

    Gordon
    Participant

    So what I understand when I bought the Archim2 it was not ready for prime-Time and it can’t support the Dual End Stops also it can’t even support the Display If that’s true then why did they sale this board to me

    #105619

    Ryan
    Keymaster

    No, that is not true. It has LCD and dual endstops (dual link).

    #105681

    Gordon
    Participant

    I downloaded and tried these three programs and the only one that worked was Marlin4Due-Archim2

    using this one MPCNC_Archim2_T8_16T_LCD_16step nothing worked no X Y or Z

    using this one Marlin-MPCNC_Archim1_T8_16T_LCD_DualEndstop nothing worked no X Y or Z

    using this on Marlin4Due-Archim2 the steppers worked but no Dual End Stops or Displays

    Nothing on E0 or E1 only X1 Y1 AND Z

    The display did not work for any of the programs

    I did Try swapping the display cables no help

    I tested the display on other machines and works just fine

    #105706

    Ryan
    Keymaster

    I answered your other thread, please keep everything in one place.

Viewing 8 posts - 1 through 8 (of 8 total)

The topic ‘Archim2 back to the Default’ is closed to new replies.