Advice – MP3DPNew Home › Forum › Milled Printed 3D Printer -MP3DP › Advice – MP3DPThis forum contains 82 topics and 527 replies, and was last updated by Mike Atencio 1 week, 1 day ago.Viewing 30 topics - 1 through 30 (of 82 total)1 2 3 →TopicVoicesPostsFreshness I have an ANET A8, can I use the parts Started by: Mike Atencio39 1 week, 1 day ago Mike Atencio Y plate or speed plate Started by: Edward24 2 weeks, 6 days ago Jeffeb3 Converting Wanhao I3 to MP3DP Started by: Teo Nordström49 3 weeks, 1 day ago Geoffrey speed plate hole size Started by: Edward25 3 weeks, 2 days ago Edward 1/2 inch Baltic birch plywood on sale at Rockler Started by: Edward11 3 weeks, 5 days ago Edward Inkscape error Started by: Edward37 3 weeks, 5 days ago Edward What are the terminals called on lever switches? Started by: SteamPunkProgrammer24 1 month ago Ryan LM8UU 3d printed replacement Started by: SteamPunkProgrammer34 1 month ago JJWHarris Steppers only move one way? Started by: SteamPunkProgrammer23 1 month ago SteamPunkProgrammer Dual Switching Extruder…What do you think? Started by: Jay33 1 month ago Dui, ni shuo de dui Differences between V1 and V2 in the 3d printed parts? Started by: SteamPunkProgrammer34 1 month ago Jeffeb3 500 x 500 x 500 MP3DP? Started by: Jay45 1 month ago Bill Autobed Levelling with TMC2100 Started by: JJWHarris412 1 month, 1 week ago Bill A4988 and DRV8825 on same ramps. Started by: Darrell22 1 month, 3 weeks ago Jeffeb3 Stepper calibration way off/correct firmware? Started by: Kirklan414 1 month, 3 weeks ago RISSOUAL Z axis smooth rods Started by: Darrell33 1 month, 3 weeks ago Bill Cost effectiveness of building mp3dp to build mpcnc Started by: Racerflea22 2 months ago Barry Thoughts and Comparisons Started by: Kenny Eaton712 3 months, 1 week ago SQLException TMC2130 Stepper Drivers Started by: Ralph722 5 months ago Ralph dual endstops noob question Started by: Rodger35 5 months, 2 weeks ago Ryan V1 frame with V2 3d parts? Started by: leader010122 5 months, 3 weeks ago Ryan Y Plate Question Started by: Robert34 5 months, 3 weeks ago Robert What hot-end/extruder Started by: David Walling413 6 months ago Rick Henderson Ramps vs Rambo mini Started by: Ralph24 6 months, 1 week ago Ryan Firmware edits to get the MP3DP running Started by: MrMeatGrinder313 6 months, 1 week ago MrMeatGrinder LEADSCREW Lead Started by: omarb24 7 months ago Ryan extruder mount Started by: omarb37 7 months, 1 week ago omarb Matterhackers E3D sale going on. Started by: Barry48 7 months, 2 weeks ago Jeffeb3 E3D TITAN AERO or MK8 style extruder Started by: Brandon55 7 months, 2 weeks ago Mmmfishtacos Micro-Swiss hotend too short Started by: David Walling323 8 months, 3 weeks ago Jeffeb3 Viewing 30 topics - 1 through 30 (of 82 total)1 2 3 →You must be logged in to create new topics.